Search Results

Search found 16950 results on 678 pages for 'android graphics'.

Page 544/678 | < Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >

  • Atheros AR2413 wireless not working after shutdown

    - by Chandrasekhar
    I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

    Read the article

  • How to show other characters in online 2D rpg

    - by Loligans
    I have Player 1 and Player 2 I am using Json to send and retrieve player data between the client and the server, but when another player logs in, and is in the same map, how would I send that data to both players to update the graphics engine to show there are 2 Players on the map? About my game it is a 2D RPG tile based game it is 24x15 Tiles it is Real time Action it should interact anywhere between 10-150 ping players interact with each other when in the same map and can see each other moving around the game world is persistent, and is saved when the server shuts down Right now the server just sends the player Only their information which is inside a Json Object Here is an example of what I am talking about If you notice there are 2 separate characters in 2 separate clients, but they are running on the same server. I am trying to get them to show up on both clients, but I don't know how I should accomplish this. Should I send it as an added value in the Json object? Also what is the name of this process so I can look it up and find more info on it?

    Read the article

  • Complete Guide/Tutorials on LWJGL?

    - by user43353
    Dont get me wrong, I finished these tutorials on http://lwjgl.org/wiki/index.php?title=Main_Page. I finished The Basics section, OpenGL 3.2 and newer section, and I looked at the Example Code section. They were great tutorials, and I have looked at the external tutorials as well. I don't know where to go from here, and OpenGL is not my strong point. Some one suggested Learning Modern 3D Graphics Programming, and I didnt learn much. I looked at the port to LWJGL, but the book was on C and I couldn't really understand what the OpenGL meant. I am trying to learn 2D gaming, not 3D. Maybe later. Is there any tutorials that aren't C/C++ heavy and teach you 2D OpenGL?

    Read the article

  • Input Signal Out of Range 1920x1080

    - by Zach
    I've recently installed Ubuntu 12.04 on my computer. Now, every time I boot and when I shut down, my monitor goes blank and says "Input Signal Out of Range - Change Setting to 1920x1080 60Hz." Once the computer gets to the login screen, it's okay again. This problem also happens when I try to open any 3d app. My graphics card is NVIDIA GEforce 6150 SE. I tried updating the drivers, but it broke everything and I had to reinstall Ubuntu. Any help?

    Read the article

  • Horible lag on Xubuntu media center setup

    - by William
    I am setting up a media center running Xubuntu 11.10 as a media center. It is using the XFCE desktop enviroment. I have the NVIDIA drivers installed from the Additional Drivers program, and uninstalled all but the esennitial software. The computer is a Dell Dimension 3000. You can view detailed technical specifications here. The graphics card installed is a Geforce 8400 GS. I have installed all updates through Update Manager. What can I do to fix the horrible lag? It makes watching TV impossible.I have uploaded two videos of the lag, here and here. The second one does not have sound because the sound stops playing on some channels that lag a lot. The TV card is a Hauppage 950q USB, and the TV recording program is Kaffiene. Please help me with this, I am trying to do this to show how great Ubuntu is to the rest of the family.

    Read the article

  • After upgrading to 13.04 Unity interface is not showing

    - by ?????? ?????
    I've upgraded to Raring last night. The upgrade itself went okay, no errors. But when I rebooted the computer afterwards and logged in to my Unity session, all I could see was the Desktop background (together with Desktop icons), and no Unity interface. The Super button shortcut wasn't showing the Dash, there was no top panel etc. Please see the screenshot. As a hint, I'm suspecting it's got something to do with my switchable graphics. I'm running Ubuntu on Acer Aspire AS5830TG with nVidia GT540M and an Intel integrated card. In 12.10 I was using Bumblebee to manage the graphic card switching. During the upgrade I saw something related to nvidia had to be uninstalled, but didn't pay much attention to it. I can't be sure if it has anything to do with my problem though. What could possibly go wrong?

    Read the article

  • Stepping outside Visual Studio IDE [Part 1 of 2] with Eclipse

    - by mbcrump
    “If you're walking down the right path and you're willing to keep walking, eventually you'll make progress." – Barack Obama In my quest to become a better programmer, I’ve decided to start the process of learning Java. I will be primary using the Eclipse Language IDE. I will not bore you with the history just what is needed for a .NET developer to get up and running. I will provide links, screenshots and a few brief code tutorials. Links to documentation. The Official Eclipse FAQ’s Links to binaries. Eclipse IDE for Java EE Developers the Galileo Package (based on Eclipse 3.5 SR2)  Sun Developer Network – Java Eclipse officially recommends Java version 5 (also known as 1.5), although many Eclipse users use the newer version 6 (1.6). That's it, nothing more is required except to compile and run java. Installation Unzip the Eclipse IDE for Java EE Developers and double click the file named Eclipse.exe. You will probably want to create a link for it on your desktop. Once, it’s installed and launched you will have to select a workspace. Just accept the defaults and you will see the following: Lets go ahead and write a simple program. To write a "Hello World" program follow these steps: Start Eclipse. Create a new Java Project: File->New->Project. Select "Java" in the category list. Select "Java Project" in the project list. Click "Next". Enter a project name into the Project name field, for example, "HW Project". Click "Finish" Allow it to open the Java perspective Create a new Java class: Click the "Create a Java Class" button in the toolbar. (This is the icon below "Run" and "Window" with a tooltip that says "New Java Class.") Enter "HW" into the Name field. Click the checkbox indicating that you would like Eclipse to create a "public static void main(String[] args)" method. Click "Finish". A Java editor for HW.java will open. In the main method enter the following line.      System.out.println("This is my first java program and btw Hello World"); Save using ctrl-s. This automatically compiles HW.java. Click the "Run" button in the toolbar (looks like a VCR play button). You will be prompted to create a Launch configuration. Select "Java Application" and click "New". Click "Run" to run the Hello World program. The console will open and display "This is my first java program and btw Hello World". You now have your first java program, lets go ahead and make an applet. Since you already have the HW.java open, click inside the window and remove all code. Now copy/paste the following code snippet. Java Code Snippet for an applet. 1: import java.applet.Applet; 2: import java.awt.Graphics; 3: import java.awt.Color; 4:  5: @SuppressWarnings("serial") 6: public class HelloWorld extends Applet{ 7:  8: String text = "I'm a simple applet"; 9:  10: public void init() { 11: text = "I'm a simple applet"; 12: setBackground(Color.GREEN); 13: } 14:  15: public void start() { 16: System.out.println("starting..."); 17: } 18:  19: public void stop() { 20: System.out.println("stopping..."); 21: } 22:  23: public void destroy() { 24: System.out.println("preparing to unload..."); 25: } 26:  27: public void paint(Graphics g){ 28: System.out.println("Paint"); 29: g.setColor(Color.blue); 30: g.drawRect(0, 0, 31: getSize().width -1, 32: getSize().height -1); 33: g.setColor(Color.black); 34: g.drawString(text, 15, 25); 35: } 36: } The Eclipse IDE should look like Click "Run" to run the Hello World applet. Now, lets test our new java applet. So, navigate over to your workspace for example: “C:\Users\mbcrump\workspace\HW Project\bin” and you should see 2 files. HW.class java.policy.applet Create a HTML page with the following code: 1: <HTML> 2: <BODY> 3: <APPLET CODE=HW.class WIDTH=200 HEIGHT=100> 4: </APPLET> 5: </BODY> 6: </HTML> Open, the HTML page in Firefox or IE and you will see your applet running.  I hope this brief look at the Eclipse IDE helps someone get acquainted with Java Development. Even if your full time gig is with .NET, it will not hurt to have another language in your tool belt. As always, I welcome any suggestions or comments.

    Read the article

  • How to perform a detailed and quick 3D performance test

    - by gsedej
    I am wondering how to quickly test performance of my 3D graphics. Since glxgears is not benchmark what should I use. Also glxgears sometimes stuck at 60FPS, you cannot even compare before/after driver update (e.g. adding xorg-edgers PPA). Even glxgears doesn't really work out of box. One possibility is screensavers, but you can't see FPS. I am also not willing to install 600MB nexuiz, specially if I am running on Live-CD. Other 3D games are also very big... Unigine tests are too demanding for opensource drivers (problems with too low OpenGL and probably texture compression (S3TC...)). I would also like to test OpenGL 2.x extentions. How to quickly test your 3D performance?

    Read the article

  • Install AMDCONFIG on Ubuntu driver

    - by Nick Bailuc
    In 12.04 I used the official driver downloaded from amd.com which came with amdconfig but now in 14.04 the official driver is buggy so I just use the Ubuntu Official Drivers which works even better because they beefed up the original driver. The Ubuntu driver doesnt come with the terminal command amdconfig which allowed me to tweak/overclock my graphics card. How can I install it without having to install the original AMD driver? Additional Information: -I only use x.org drivers becuase it's opensource therefore more stable rather than the proprietary fglrx driver -I do not use procrams like amdoverdrivectrl or atioverclock because they are not as stable and advanced as the terminal command

    Read the article

  • How to Access Boot Options 12.04 Live USB

    - by Ryan Kampmeier
    I'm attempting to install 12.04 on my computer but booting from my USB drive results in a blank screen. This has happened since 10.04 and has always been fixed by putting nomodeset in the boot command, but now I can't access the boot options with F6 for some reason. How can I access the boot options? I booted into the live image on a different computer and it worked fine. I'm sure it's because of my Nvidia graphics. When I boot into the live image it shows a small gray box in the lower left corner of the screen and that's it. I can't edit the boot options or do anything else. Thanks in advance.

    Read the article

  • Lenovo u400, Ubuntu 12.04. Sudden reboots / power down

    - by Victor Neo
    I've recently bought a Lenovo u400 (http://www.lenovo.com/products/us/laptop/ideapad/u-series/u400/) and installed Ubuntu 12.04 on it. Everything works fine (I've installed the proprietary ATI drivers for switchable graphics) except that I get a random power down or reboot either while surfing the web or watching videos. Monitoring the temperature with sensors, the laptop never goes into any critical zone but still may power down or reboot once in a while. Is there any logs that I should check and any particular message I should take note of? EDIT: This happens to me as well. This also happens without proprietary drivers activated.

    Read the article

  • Very High CPU usage (100%) from just browsing the Web

    - by cole
    I tested on Firefox and Chromioum. Im at 100% while loading pages which causes them to load slow and when I dont have a application running Im at 40% CPU (At least) Everything is slow basically. Im also already on Ubuntu Classic so im not using Unity. Should I go to 10.04? is that more stable? On windows this wasnt an issue. I have a Dual Boot with XP and a 2.4Ghz Intel Celeron with 768MB RAM and an Nvidia 6200 Graphics card. I heard 10.04 was the most stable. any suggestions?

    Read the article

  • Right tool for the job(html5 vs silverlight)

    - by Jargo
    I have been tasked to develop a web based offer request application for bathrooms and I am asking opinions on which tool should I choose. I have narrowed options down to two (html5 and silverlight). Most of the application consists of basic UI elements that could be achieved with html4. However most challenging part is the design view for the bathroom. User first defines size of the bathroom by giving dimensions. When the dimensions are defined the application renders an empty bathroom floorplan and user can start dragging&dropping furniture on to it. Some furniture have rules where they can be dragged. For example sinks can only be dragged next to a wall. I know that this functionality can be achieved with silverlight but what about html5 ? I know that Canvas element can be used to draw graphics, but can it render the bathroom smoothly as user drags a piece furniture on it?

    Read the article

  • Multiple Monitors using nvidia-prime or bumblebee on Ubuntu 13.10

    - by user205626
    I've been unable to get multiple monitors to work with Ubuntu 13.10 using nvidia-prime or bumblebee. Could someone point me in the right direction? With nvidia-prime, I've tried the xorg.conf here http://us.download.nvidia.com/XFree86/Linux-x86/319.12/README/randr14.html, but I boot into "low graphics" mode and have to revert to get a desktop back. Any suggestions would be appreciated. Thanks. Edit: I've given up on nvidia-prime; I missed the fact that it never turns off the discrete card... So, I'm back to trying to get VIRTUAL displays working with Bumblebee.

    Read the article

  • Frequent GUI pauses in Ubuntu 13.04 / Unity / Intel HD4000

    - by Simon
    I'm experiencing very frequent (and regular) GUI pauses on my system. Every 30 seconds (pretty much exactly) the GUI will freeze for maybe .25 to .5 seconds. The mouse stops moving, keys stop echoing and a stopwatch timer briefly pauses. I'm using the Intel Graphics driver available from: https://download.01.org/gfx/ubuntu/13.04/main I've looked in a few places and tried a few things for a solution: I've checked cron and anacron for scheduled processes. I've disabled background processes (eg mysql, postgres, apache) not that these were doing anything anyway I've checked the following posts and tried the suggestions there: Unity GUI pauses/freezes for less than a few seconds How to go about troubleshooting frequent system pauses I've watched the system using top and System Monitor and there are no spikes (or even blips) of cpu usage when the pauses occur. There are no obvious error messages in dmesg or syslog There is loads of free RAM (8GB+) and no swap usage If it helps it's a ZooStorm i5 laptop with a HD4000 GPU, 16GB Ram and an SSD. Any help / suggestions would be very gratefully received.

    Read the article

  • What is the practical use of IBOs / degenerate vertex in OpenGL?

    - by 0xFAIL
    Vertices in 3D models CAN get cut in the process of optimizing 3D geometry, (degenerate vertices) by 3D graphics software (Blender, ...) when exporting because they aren't needed when reusing a vertex for multiple triangles. (In the current case 3D data is exported from Blender as .ply and read by a simple application that displays the 3D model) Every vertex has a few attributes like position, color, normal, tangent,... But the data for each vertex that is cut through the vertex sharing is lost and is missing in the vertex shader. Modern shader techniques like Bump or Normal mapping require normals/tangents per vertex which are also cut. To use complex shader techniques IBOs must not be used? Or is there a way to use IBOs and retain the data per vertex that was origionally lost?

    Read the article

  • Ubuntu 12.10 desktop/interface not showing on VirtualBox VM after login screen

    - by Jake
    I'm having some trouble with getting my Ubuntu to work on a VirtualBox VM. I made a clean installation of Ubuntu 12.10 on a VM without any errors. I arrive at the login screen, as soon as I press enter it does it's little loading thingy and then screen goes black, then this is all I get: http://i.imgur.com/zULUI.jpg I can access the terminal and pretty much all the other features through it, but I would like to have the GUI properly working. I've been looking around the web and looking at various fixes to similar problems, but can't seem to get it to work. I'm thinking this problem might have to do with the graphics? I'm running Windows 8 Pro as host, if that helps, might be some compatibility issues with VirtualBox in W8... Thanks in advance!

    Read the article

  • OpenGL 3 and the Radeon HD 4850x2

    - by rotard
    A while ago, I picked up a copy of the OpenGL SuperBible fifth edition and slowly and painfully started teaching myself OpenGL the 3.3 way, after having been used to the 1.0 way from school way back when. Making things more challenging, I am primarily a .NET developer, so I was working in Mono with the OpenTK OpenGL wrapper. On my laptop, I put together a program that let the user walk around a simple landscape using a couple shaders that implemented per-vertex coloring and lighting and texture mapping. Everything was working brilliantly until I ran the same program on my desktop. Disaster! Nothing would render! I have chopped my program down to the point where the camera sits near the origin, pointing at the origin, and renders a square (technically, a triangle fan). The quad renders perfectly on my laptop, coloring, lighting, texturing and all, but the desktop renders a small distorted non-square quadrilateral that is colored incorrectly, not affected by the lights, and not textured. I suspect the graphics card is at fault, because I get the same result whether I am booted into Ubuntu 10.10 or Win XP. I did find that if I pare the vertex shader down to ONLY outputting the positional data and the fragment shader to ONLY outputting a solid color (white) the quad renders correctly. But as SOON as I start passing in color data (whether or not I use it in the fragment shader) the output from the vertex shader is distorted again. The shaders follow. I left the pre-existing code in, but commented out so you can get an idea what I was trying to do. I'm a noob at glsl so the code could probably be a lot better. My laptop is an old lenovo T61p with a Centrino (Core 2) Duo and an nVidia Quadro graphics card running Ubuntu 10.10 My desktop has an i7 with a Radeon HD 4850 x2 (single card, dual GPU) from Saphire dual booting into Ubuntu 10.10 and Windows XP. The problem occurs in both XP and Ubuntu. Can anyone see something wrong that I am missing? What is "special" about my HD 4850x2? string vertexShaderSource = @" #version 330 precision highp float; uniform mat4 projection_matrix; uniform mat4 modelview_matrix; //uniform mat4 normal_matrix; //uniform mat4 cmv_matrix; //Camera modelview. Light sources are transformed by this matrix. //uniform vec3 ambient_color; //uniform vec3 diffuse_color; //uniform vec3 diffuse_direction; in vec4 in_position; in vec4 in_color; //in vec3 in_normal; //in vec3 in_tex_coords; out vec4 varyingColor; //out vec3 varyingTexCoords; void main(void) { //Get surface normal in eye coordinates //vec4 vEyeNormal = normal_matrix * vec4(in_normal, 0); //Get vertex position in eye coordinates //vec4 vPosition4 = modelview_matrix * vec4(in_position, 0); //vec3 vPosition3 = vPosition4.xyz / vPosition4.w; //Get vector to light source in eye coordinates //vec3 lightVecNormalized = normalize(diffuse_direction); //vec3 vLightDir = normalize((cmv_matrix * vec4(lightVecNormalized, 0)).xyz); //Dot product gives us diffuse intensity //float diff = max(0.0, dot(vEyeNormal.xyz, vLightDir.xyz)); //Multiply intensity by diffuse color, force alpha to 1.0 //varyingColor.xyz = in_color * diff * diffuse_color.xyz; varyingColor = in_color; //varyingTexCoords = in_tex_coords; gl_Position = projection_matrix * modelview_matrix * in_position; }"; string fragmentShaderSource = @" #version 330 //#extension GL_EXT_gpu_shader4 : enable precision highp float; //uniform sampler2DArray colorMap; //in vec4 varyingColor; //in vec3 varyingTexCoords; out vec4 out_frag_color; void main(void) { out_frag_color = vec4(1,1,1,1); //out_frag_color = varyingColor; //out_frag_color = vec4(varyingColor, 1) * texture(colorMap, varyingTexCoords.st); //out_frag_color = vec4(varyingColor, 1) * texture(colorMap, vec3(varyingTexCoords.st, 0)); //out_frag_color = vec4(varyingColor, 1) * texture2DArray(colorMap, varyingTexCoords); }"; Note that in this code the color data is accepted but not actually used. The geometry is outputted the same (wrong) whether the fragment shader uses varyingColor or not. Only if I comment out the line varyingColor = in_color; does the geometry output correctly. Originally the shaders took in vec3 inputs, I only modified them to take vec4s while troubleshooting.

    Read the article

  • Drawing different per-pixel data on the screen

    - by Amir Eldor
    I want to draw different per-pixel data on the screen, where each pixel has a specific value according to my needs. An example may be a random noise pattern where each pixel is randomly generated. I'm not sure what is the correct and fastest way to do this. Locking a texture/surface and manipulating the raw pixel data? How is this done in modern graphics programming? I'm currently trying to do this in Pygame but realized I will face the same problem if I go for C/SDL or OpenGL/DirectX.

    Read the article

  • How can I reconfigure the nvidia proprietary drivers from the command line (ssh)?

    - by Mathieu Pagé
    I have a linux HTPC (running XBMC) in my living room. This morning I ssh'ed into the machine and did upgrade it to 10.10. When it finaly resarted it says something about running in low quality graphics and eventually returned to a command line login prompt. I ssh'ed in again and did a sudo reboot now. When it came back on this time the image is rapidly scrolling from the top to the bottom of the screen. I guess the installed driver doesn't quite work with the S-Video port on which the TV is connected. previously it was working right with the nvidia proprietary drivers. How can I install thoses without using the GUI tool that comes with Ubuntu?

    Read the article

  • packhard bell dot s netbook ubuntu 12.10

    - by Kermit
    sorry im absolutly linux beginner.... i bought a packhard bell netbook dots with Limpus.did not get along with limpus so wanted to install ubuntu. netbook: 2 GB RAM intel Atom N2600, intel graphics Media Accelerator 3600 I over installled ubuntu 12.10 (desktop version) like in the instruction (isofile over USB). Installation went fine. No problems. when starting after installation alot of text is coming.....starting xyz....with alot of okays at the end of line but nothing happends: ends with #Starting CPU interrups balancing daemon, stopping anachronics cron and blinking cursor... was reading in this forum, tried to do some things like #recoverymode# and nomodeset... but did not work or where do i get this graphic drivers from. Packard bell just offers windows drivers.and how do i install them? maybe its a completely diffrent cause for this? Thanks alot

    Read the article

  • Ubuntu 12.04 crashing

    - by James Mullinix
    We have a server with 2x32gb sas raid 1 and 4x1tb raid 10 + 2x1tb hot spares. Whenever we try to copy the 1tb and 1.5e6 files to a backup location (even just using tty1 cp command) it fails. We have tried using backintime and dejadup, and resorted to a manual cp to an external usb2 HDD. When that failed, we tried installing an internal HDD on the mobo (not on raid) and another cp, which also fails. The failures lock up the system and we are left with an unfortunate hard reboot situation. After reboot, syslog tends to be empty (only containing newly booted data) and we haven't a clue where to start. It has been 3 weeks since our last successful backup and we are getting nervous... -using 3ware raid controller, 8gb ram and nvidia pciexpress graphics with a gigabyte mobo and xeon 4-core processor.

    Read the article

  • GNOME 3.4 released, with smooth & fast magnification

    - by Peter Korn
    The GNOME community released GNOME 3.4 today. This release contains several new accessibility features, along with a new set of custom high-contrast icons which improve the user experience for users needing improved contrast. This release also makes available the AEGIS-funded GNOME Shell Magnifier. This magnifier leverages the powerful graphics functionality built into all modern video cards for smooth and fast magnification in GNOME. You can watch a video of that magnifier (with the previous version of the preference dialog), which shows all of the features now available in GNOME 3.4. This includes full/partial screen magnification, a magnifier lens, full or partial mouse cross hairs with translucency, and several mouse tracking modes. Future improvements planned for GNOME 3.6 include focus & caret tracking, and a variety of color/contrast controls.

    Read the article

  • How is the terrain generated in Commandos and Commandos game clones/look-alikes?

    - by teodron
    The Commandos series of games and its similar western counterpart, Desperados, use a mix of 2D and 3D elements to achieve a very pleasing and immersive atmosphere. Apart from the concept that alone made the series a best-seller, the graphics eye-candy was also a much appreciated asset of that game. I was very curious on what was the technique used to model and adorn the realistic terrains in those titles? Below are some screenshots that could be relevant as a reference for whomever has a candidate answer: The tiny details and patternless distribution of ornamental textures make me think that these terrains were not generated using a standard heightmap-blendmap method.

    Read the article

  • Can I hook my xbox up to my Ubuntu PC

    - by Anonymous John
    My old xbox 360 won't eject disks, it makes a sound,but won't open. I want to play games, so I think I could hook it up to my PC running Ubuntu 13.10 64-bit and maybe I could use my PC's DVD drive. Can this work at all, or am I just crazy? There is an HDMI port on the back of my graphics card. If I can't do that, is there any software for Ubuntu that can rip the game off of a CD and put it on a flash drive? I have heard xbmcbuntu works great for gaming, but it doesn't work with my PC.

    Read the article

< Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >